Supplier Directory Subscribe
Advertisement
Advertisement
Advertisement
Advertisement
Home / Liquid-Cooled Generator Technology Reduces EDM Electrode Wear

Liquid-Cooled Generator Technology Reduces EDM Electrode Wear

A breakthrough liquid-cooled generator technology marks the next generation of CNC Die Sinking that has revolutionized the way machine tool builders look at their power supplies.

Posted: August 6, 2013

Exeron GmbH developed the exopuls+ liquid cooled generator technology, a breakthrough in the spark eroding process that has produced results that have exceeded initial expectations.
Using exopuls+, graphite electrode wear during roughing and finishing was reduced by about 35 percent, while machining efficiency increased, providing faster burn times.
Advertisement
Advertisement

Exeron GmbH (Oberndorf, Germany) developed breakthrough liquid-cooled generator technology that reduces electrode wear during roughing and finishing and provides faster burn times. Traditionally, European and Asian machine tool manufacturers preferred copper over graphite for electrodes, while North American manufacturers leaned toward graphite whenever possible. The reasons to use one or the other material have been well documented, and the merits of graphite have now spilled over into the European market.

That is good news for all those involved in Die Sinker EDM machining using graphite, because as European machine manufacturers recognized this trend, they became interested in advancing technology in this area. EDM research and development in Europe included looking at new ways to use a power supply that would be capable of fully utilizing the advantages of graphite electrodes.

Advantages of graphite include unique burning characteristics (high melting temperatures) to obtain zero percent wear. And since the quality of the surface finish of an electrode will directly translate to a mold, it is imperative to begin with a first-rate electrode. At the same time, a need to reduce both the size of the machine’s power supply, and subsequently to decrease the amount of energy consumed during erosion, was explored.

Traditionally power supplies on die sinkers were bulky, took up a large foot print and developed a great deal of heat within the power supply cabinet during the eroding process. Over time, this heat weakens the board components and reduces the efficiency of the power supply. As most EDM operators know, any change in the power supply can result in slower burning and reduced finishes.

Consistency in power output is critical to the erosion process. To keep the boards cool, large fans or heat exchangers are needed to move shop air around inside the cabinet. This design worked sufficiently, but it also allowed the components in the cabinet to get covered in oils and dirt that were suspended in the air and drawn into the power supply cabinet. This contamination is also a contributing factor in heat build-up and reduced electrical component life. If you have ever opened up the cabinet of any CNC machine, one can clearly see how dirty they can become over time. Research for a better power supply led to building a more compact and energy efficient unit, resulting in “no wear” and smoother finishes in less time. Prototypes were placed into service immediately following.

New, extremely compact power supplies are only about the size of a small laptop and are still capable of generating the same amount of cutting amperage at the electrode as larger power supplies. At the same time, new power supplies are tremendously energy efficient. To achieve the compact stature and efficiency, a unique, liquid cooled heat exchanger is integrated into the aluminum framework that holds the power generation boards sit.

The coolant used to dissipate heat in the power supply is simply the dielectric fluid already available in the machine. A small pump is included in the machine’s dielectric system that continually circulates filtered dielectric oil directly from the chiller to the power supply and back to the machine reservoir. This consistency of the cooling provides for a very stable machining process, while allowing the machine cabinet that houses the power supply to be completely sealed from outside contaminants. This design allows for years of life with little to no operator maintenance. It also eliminates the need for circulation fans, which are prone to failure over time, and draw additional electrical current. These new power supplies operate at cooler temperatures, resulting in improved input voltage stabilization.

Efficiency was also improved by reducing the cable lengths required to go from the power supply to the head of the machine. By reducing the size of the power supply, the unit can be located closer to the machine head and table to improve current transfer and grounding. The simplistic design of the power supply reduced the need for the number of boards required, and with fewer boards to contend with overall reliability of the power supply is improved.

Exeron GmbH has developed the exopuls+ liquid cooled generator technology, a break-through in the spark eroding process, which has produced results that have exceeded initial expectations. Using exopuls+, graphite electrode wear during roughing and finishing was reduced by about 35 percent, while machining efficiency increased, providing faster burn times. In some cases when using electrodes with fine details, the burn times were reduced by as much as 18 percent over previous power supplies.

Advancements in this area of EDM machining continued with an examination of the machine’s logic to further enhance burning, especially in poor flushing conditions. The new found efficiency of the power supply allowed for smoother power setting transitions (1 amp increments), which in turn, allows the CNC Die Sinkers to produce the same results with less setting changes. This makes operation of the machines much more user friendly, offering greater predictability in the final erosion results.

With regard to efficiency, the new power supply has reduced overall operating costs. The efficiency enhancements resulting from the new liquid cooled design has netted dramatic power reductions. It has been found that under a full 60 amp burn, power consumption went from 537 kWh to as low as 2.8 kWh in the same erosion application. Power dissipation was also reduced from 3000 W to 600 W. Efforts to reduce energy consumption and operating costs for the end user are important considerations for EDM manufacturers.

As was the jump from tube type power supplies to solid state, the new liquid cooled power supply marks the next generation of technology for CNC Die Sinking and has revolutionized the way machine tool builders look at their power supplies. The demand for smaller space, better performance and lower costs has now reached a new level.

Exeron GmbH, Beffendorfer Straße 6 D-78727, Oberndorf, Germany, 0-7423-8674-0, [email protected], www.exeron.de.

Subscribe to learn the latest in manufacturing.

Calendar & Events
FABTECH 2024
October 15 - 17, 2024
Orlando, FL
Design-2-Part Show
October 16 - 17, 2024
Marlborough, MA
Design-2-Part Show
October 23 - 24, 2024
Akron, OH
SEMA
November 5 - 8, 2024
Las Vegas, NV
Design-2-Part Show
November 19 - 20, 2024
Nashville, TN
Advertisement
Advertisement
Advertisement
Advertisement
Advertisement